How to set mulitpath target by targetcli?
shadowlin
67 Posts
April 22, 2018, 5:27 amQuote from shadowlin on April 22, 2018, 5:27 amI want to config a mulitpah target with redundant iscsi gateway by targetcli for some test.I tried to make targetcli ls result looks the same as petasan's but it doesn't work.
I have already known that tpg_enabled_sendtargets in configFS must be set so the initiator can find the disabled tgp, but what else did i miss?
I want to config a mulitpah target with redundant iscsi gateway by targetcli for some test.I tried to make targetcli ls result looks the same as petasan's but it doesn't work.
I have already known that tpg_enabled_sendtargets in configFS must be set so the initiator can find the disabled tgp, but what else did i miss?
admin
2,930 Posts
April 22, 2018, 10:52 amQuote from admin on April 22, 2018, 10:52 amI recommend you use the ui to set it up rather than manual. we do not use targetcli ourselves.
I recommend you use the ui to set it up rather than manual. we do not use targetcli ourselves.
shadowlin
67 Posts
April 24, 2018, 12:19 pmQuote from shadowlin on April 24, 2018, 12:19 pmI can't use the UI for my old cluster which was deployed without petasan.
Are you using rtslib to manipulate lio?
Could you give me some hints about how to setup redundant iscsi gateway ?
I can't use the UI for my old cluster which was deployed without petasan.
Are you using rtslib to manipulate lio?
Could you give me some hints about how to setup redundant iscsi gateway ?
admin
2,930 Posts
April 24, 2018, 4:04 pmQuote from admin on April 24, 2018, 4:04 pmwe do use rtslib to configure lio directly. You can also use lrbd tool which is also supplied in the install.
we do use rtslib to configure lio directly. You can also use lrbd tool which is also supplied in the install.
shadowlin
67 Posts
April 25, 2018, 12:25 pmQuote from shadowlin on April 25, 2018, 12:25 pmOK
Thank you
OK
Thank you
How to set mulitpath target by targetcli?
shadowlin
67 Posts
Quote from shadowlin on April 22, 2018, 5:27 amI want to config a mulitpah target with redundant iscsi gateway by targetcli for some test.I tried to make targetcli ls result looks the same as petasan's but it doesn't work.
I have already known that tpg_enabled_sendtargets in configFS must be set so the initiator can find the disabled tgp, but what else did i miss?
I want to config a mulitpah target with redundant iscsi gateway by targetcli for some test.I tried to make targetcli ls result looks the same as petasan's but it doesn't work.
I have already known that tpg_enabled_sendtargets in configFS must be set so the initiator can find the disabled tgp, but what else did i miss?
admin
2,930 Posts
Quote from admin on April 22, 2018, 10:52 amI recommend you use the ui to set it up rather than manual. we do not use targetcli ourselves.
I recommend you use the ui to set it up rather than manual. we do not use targetcli ourselves.
shadowlin
67 Posts
Quote from shadowlin on April 24, 2018, 12:19 pmI can't use the UI for my old cluster which was deployed without petasan.
Are you using rtslib to manipulate lio?
Could you give me some hints about how to setup redundant iscsi gateway ?
I can't use the UI for my old cluster which was deployed without petasan.
Are you using rtslib to manipulate lio?
Could you give me some hints about how to setup redundant iscsi gateway ?
admin
2,930 Posts
Quote from admin on April 24, 2018, 4:04 pmwe do use rtslib to configure lio directly. You can also use lrbd tool which is also supplied in the install.
we do use rtslib to configure lio directly. You can also use lrbd tool which is also supplied in the install.
shadowlin
67 Posts
Quote from shadowlin on April 25, 2018, 12:25 pmOK
Thank you
OK
Thank you